Most commonly, it is used in severe service (above or below the water line) in marine applications where these resistance qualities are desired. Its excellent wetting properties allows it to penetrate rust and discontinuities in existing coatings and provide a firm anchorage for a variety of topcoats. It exhibits excellent resistance to splash and spillage of salts and water. It provides both hydrocarbon and cellulosic fire protection for structural steel and can also be used to upgrade the fire resistance of existing concrete. Aluminium-pigmented, low-stress, high solids mastic with a proven field history. It fully meets criteria of API RP 5L2 for gas transmission pipelines. Not recommended for immersion service, splash and spillage of acids, alkalies or solvents. A 40 lb./ft³ (640 kg/m³) density, Portland cement based, cementitious fireproofing. Has excellent resistance to a wide range of solvents, alkalies, cleaning solutions and acids entrained vapours of high concentration. Some recommended uses of 1340 include the use as a curing compound or form release agent. Low temperature cure down to 0°F (-18°C). It can be used to minimize or eliminate sweating of pipes or other operating equipment. reinforcement (micaceous iron oxide) to enhance Compatible over most coatings and old paint, is readily topcoated with many generic types. Polyclad 975 cures fast to allow quick QC and backfill times.Polyclad 975 is designed for spray application. This product has excellent wetting properties giving it the capability of going over marginally prepared substrates. Renowned high build coal tar epoxy for protection of steel and concrete in single or two-coat applications in a broad variety of aggressive industrial applications. Rapid cure.Dry to handle in 30 minutes at 75°F (24°C) and 60% RH, Can be topcoated in 4-5 hours at 75°F/24°C and minimum 60% RH, Tolerant to mudcracking (up to 6 mils/150 microns), Smooth uniform texture reduces topcoat bubbling, May be applied with standard airless or conventional spray equipment, Low HAPs content of 0.12 lbs/solid gallon, Meets Class B slip co-efficient and creep testing criteria for use on faying surfaces, Rapid cure. UL listed - designs for many types of steel sections up to 4 hour fire ratings for both interior and exterior environments. Carboline’s coatings for new construction provide long-term protection against chemical, abrasive, high-temperature, and extreme atmospheric environments. Adheres to API 653 inspection and API 652 guidelines for inspection intervals. It contains high levels of inert flake reinforcement. Markets served are terminals, refineries, petrochemical, wastewater, railcar linings, subsea oil and gas equipment, and many others. 1205 exhibits very good acid resistance. Highly chemical resistant epoxy mastic coating with exceptionally versatile uses in all industrial markets. Carboline | Product Details. If you do not wish to accept cookies from this website, you can choose to not allow cookies from this website by updating your browser preferences. *, Meets the FDA requirements for 21CFR 175.300 for direct food contact, Handles deionized water up to 150°F (66°C), Suitable for application to tight rust and ISO 8501 St2 and St3 cleaned substrates, Used as a primer or an intermediate coating. If you click the "Accept All Cookies" button or continue navigating the website, you agree to having those first and third-party cookies set on your device. Carboguard 165 is a solvent-free, surface tolerant, single coat epoxy system which provides excellent protection against fumes, frequent splash and spillage. A single-component, high performance coating which has outstanding resistance to wet / dry cycling conditions at elevated temperatures. Surface is easily cleaned. Carbomastic 15 was the pioneer mastic coating in a number of industrial markets and today still provides unmatched levels of barrier protection and corrosion resistance over existing finishes and rusted or SSPC-SP2 or SP3-cleaned steel. High build, low sheen finish that has excellent resistance to corrosion, chemicals and abrasion. High performance, high solids, epoxy lining that is recommended for a variety of petroleum storage products including 180°F (82°C) crude oil, demineralized water 150°F (65°C), crude/water mixtures, fuel oil, jet fuel, biodiesel, and gasoline. Excellent for use as a lining for tanks or pipes in process facilities where hot water or abrasive conditions exist. Plasite 7122 VTF, is a PTFE filled tank lining for use where the surface requires release properties to reduce product sticking and bridging. Thermaline Heat Shield contains a unique blend of plate-like reinforcing pigments fortified with an inert polymeric matrix. This Typical uses include pipeline exterior surfaces. This lining-grade epoxy has wide chemical resistance and is suitable for use as a chemically resistant coating for aggressive atmospheric exposures or as a lining for a variety of chemical exposures. Polyclad 975 H cures fast to allow quick QC and backfill times. View products by brand name, application type or market. Ultra-durable solvent-free coating for use on steel and concrete substrates subject to severe impact and physical abuse. If you do not wish to accept cookies from this website, you can choose to not allow cookies from this website by updating your browser preferences. Carbozinc 11 meets Class B slip co-efficient and creep testing criteria for use on faying surfaces. It is particularly well suited to prevent corrosion under insulated equipment/piping for both carbon steel substrates and stainless steels. PLASITE 4550 S is a 100% solids, flake filled, premium novolac epoxy coating designed for internal steel and concrete substrates. Durable finish - provides a hard, durable finish resistant to normal wear. tolerance during application, low temperature cure as a primer, intermediate coat, or self-priming A dense cross-linked polymer which exhibits outstanding barrier protection against a variety of chemical exposures. Single package coating that withstands continuous temperatures of 540°C and surges up to 650°C. Once applied, it meets code and insurance requirements for interior and exterior use. film strength and performance. Contains additional filler reinforcement (micaceous iron oxide) for enhanced barrier resistant properties. This product has excellent wetting properties giving it the capability of going over marginally prepared substrates. The combination of the zinc primer with this finish provides exceptional performance in durability. A water-resistant, phenolic epoxy coating polymerized with a polyamine type curing agent. Single package primer, resistant to spillage of mild acids and alkalies, aliphatic solvents, etc., with suitable topcoat. Rustbond Penetrating Sealer is a crosslinking penetrating sealer with excellent wetting properties. This aluminum-pigmented epoxy also contains inert flake reinforcement (micaceous iron oxide) to enhance film strength and performance. Recommended areas of application include refineries, petrochemical, pharmaceutical facilities, pulp and paper mills, offshore platforms, nuclear and conventional power plants, factories, warehouses, institutional and biomedical facilities. Weld spatter does not adhere to or damage the coating, Can be welded as quickly and easily as bare steel at production line speeds without loss in strength or consistency of the weld, Dries to touch and to handle in 3 to 5 minutes, Certified as a pre-construction primer for Lloyds Register constructions. Pyroclad X1 is designed to provide jet fire and hydrocarbon fire protection for structural elements, beams, columns, bulkheads, underdecks and risers. After curing, the coating is very resistant to thermal shock conditions from ambient temperatures to 400°C. It is highly flexible with good chemical and solvent resistance, and accepts a variety of topcoats. May be used as a self-priming or finish coat on exterior exposure if discoloration can be tolerated. Can also be used interior as a high gloss maintenance product with ease of use characteristics. It can be also be used for buried pipe due to its outstanding physical durability. High solids, high gloss, finish with 30% silicone modification that provides excellent weathering performance as an exterior enamel. A solvent-less, high gloss, smooth epoxy coating for the lining of gas transmission pipelines. Its excellent wetting properties allows it to penetrate rust and discontinuities in existing coatings and provide a firm anchorage for a variety of topcoats. Can be used direct to metal as a corrosion resistant primer or as an intermediate coating over other primers. Semstone 5301HT is a highly versatile epoxy novolac vinyl ester coating and lining system with a unique combination of toughness and resistance to mechanical abuse along with excellent resistance to a wide range of chemical exposures. It is widely used as a tank lining for steel and concrete tanks. It provides both hydrocarbon and cellulosic fire protection for structural steel and can also be used to upgrade the fire resistance of existing concrete. Consult StonCor Africa for specific recommendations. CAR 200 can be overcoated with CAR 100 to provide a smooth surface that will improve flow and equipment efficiency. Carbomastic 18 BT is a fast-curing, heavy-duty, high-build anti-corrosive coating with a broad and versatile list of uses in marine and other corrosive environments. Plural component spray equipment is not required. If you click the "Accept All Cookies" button or continue navigating the website, you agree to having those first and third-party cookies set on your device. High performance lining system designed for concrete. Because it bonds directly to the surface (unlike standard insulation materials) it minimizes water entry and the effect of corrosion under insulation. Excellent for crude oil storage and transportation up to 250° F (121° C), Excellent resistance to deionised water up to 93°C, Excellent resistance to crude oil up to 82°C, May be used to line tanks or pipes in process facilities, where hot water solutions or abrasive conditions exist, Excellent as secondary containment lining for a variety of chemicals. Typical uses include steel pipeline exteriors, steel valves & fittings, steel pilings, steel poles (above & below ground), buried tank exteriors, penstocks. Carbothane 137 HS is a fast-drying, high build, two component polyurethane coating which exhibits excellent dry times and handling characteristics required by Original Equipment Manufacturers. Only one coat is required, but may be applied over Carbozinc 11 base coat for superior performance. It may be applied in a single coat application up to 400 microns without slumping. Carbomastic 15 was the pioneer mastic coating in a number of industrial markets and today still provides unmatched levels of barrier protection and corrosion resistance over existing finishes and rusted or ISO 8501 St2 or St3 cleaned steel. Dry to handle in 45 minutes at 60°F (16°C) and 50% relative humidity. Excellent thermal shock resistance (0 to 300° F). Rapid cure. Self-priming epoxy lining with excellent adhesion, flexibility and abrasion resistance. It has excellent flexibility and good abrasion resistance. When applied to “green” concrete it will retard the escape of moisture during the cure period. It provides both hydrocarbon and cellulosic fire protection for structural steel and can also be used to upgrade the fire resistance of existing concrete. It is self-priming. Is excellent as a … VOC compliant to current AIM regulations. No primer is required. Consult Carboline Tech Service for high profile non-skid applications. It is designed to increase flow efficiency of natural gas in pipelines. It meets VOC regulations while providing the proven performance of silicate zinc rich technology. Suitable for insulated or uninsulated pipes, stacks and equipment operating up to 450 °F (232 °C). Excellent resistance to acids, caustics, ethanol, gasoline, jet fuels and solvents. It can handle cryogenic exposures and will cure effectively at ambient conditions to provide corrosion protection without additional heat curing. Carboline Africa Headquarters - 8 Cresset Road, Midrand Industrial Park - Johannesburg, South Africa ; Phone: +27 (0)11-254-5500 ), Dense, highly cross-linked film for superior barrier protection, Excellent abrasion resistance and toughness, Meets NORSOK System 7C Requirements for subsea equipment up to 356°F (180°C), Excellent resistance to petroleum products, Single coat external corrosion protection, Carboguard 920 Glass Flake may be added to improve film properties, Batch mix formulation, single leg airless spray, Excellent resistance to water and salt water, Passes EI 1541 requirements for internal protective coating systems used in aviation fuel handling systems, including the jet fuel gum test. Recommended areas of application include refineries, petrochemical, pharmaceutical facilities, pulp and paper mills, offshore platforms, nuclear and conventional power plants, factories, warehouses, institutional and biomedical facilities. It is an ideal protective heat barrier to shield personnel from hot surfaces. Recommended for Original Equipment Manufacturers where a high performance, highly corrosion resistant zinc primer is desired. Carboguard 60 is a high solids, versatile, abrasion resistant, chemical resistant, and corrosion resistant coating. 100% solids, high performance, novolac epoxy lining system designed for concrete. resistance to fresh and salt water exposures. Air-dried coating available in colors and suitable for high temperature exposures up to 500°F (260°C). If you do not wish to accept cookies from this website, you can choose to not allow cookies from this website by updating your browser preferences. Dense, highly impermeable glass flake-filled coating used for protecting steel and concrete. Widely used as a tank lining system in the petrochemical industry as well as in other aggressive immersion conditions like jet fuel, municipal and industrial waste water. This low temperature cure formulation allows application and curing down to 35°F (2°C). A high performance lining for elevated temperature and pressure immersion services in high purity water, as well as the oil/water separating processes encountered in the petroleum industry. For more information on how we use Cookies, please read our Privacy Policy. StonCor Africa (Pty) Ltd is the South African operating company for RPM Performance Coatings, which has its head office in New Jersey USA. Phenoline 353 LT is a highly cross-linked epoxy lining with extraordinary overall chemical resistance and versatility. Provides excellent protection in mild environments. It is an excellent choice for the protection of ship hull exteriors, underwater and ballast tanks. For over five decades, Carbozinc 11 Series primers have been the industry standard for high-performance inorganic zinc protection on steel structures worldwide. Can be applied by conventional and airless spray. Thin film, high gloss finish with exceptional weathering performance characteristics. Carboline glass flake additive may be added to improve performance including internal strength, hardness, impact, and abrasion resistance. Has surface tolerant properties. Carbothane 134 is a glossy, tile-like, attractive topcoat, produces a smooth, slick and hard film which is readily cleaned. It can be used as a primer or an intermediate coat over recommended primers. Rapid cure. It performs extremely well in sealing cementitious surfaces and is designed to receive a variety of different generic types of finish coats. Aluminium platelets form a labyrinth which provides excellent resistance to penetration. Low VOC organic zinc epoxy steel primer with extremely fast cure-to-topcoat characteristics for in-shop applications and quick turnaround requirements in the field. It is a unique blend of resins and curing agents that allow batch mixing for ease of application. Ultra high solids epoxy that is designed as a liner for potable water, demineralized water, wastewater and many other services. This product is ideal for industrial or heavy duty marine environments for the protection of steel against salt laden environments. Typical uses include steel pipeline exteriors, steel valves & fittings, steel pilings, steel poles (above & below ground), buried tank exteriors, penstocks. Excellent touch-up primer by brush or roller for small areas. This website uses cookies and other tracking technologies (also known as pixels or beacons) to aid your experience (such as viewing videos), as well as “performance cookies” to analyze your use of this website and to assist with marketing efforts. It can be used as a primer, intermediate coat, or self-priming finish over steel or inorganic zinc primers. High solids, high-build potable water coating widely used for lining interior steel and concrete tanks, valves and pipes. Alumanation 301 contains no asbestos. It may also be used as a tie-coat for coatings that exceed their “recoat window.” Consult Carboline Technical Services Department for specific recommendations. Serves as stand-alone system for a variety of chemical environments and is also designed for various immersion conditions. Its thixotropic character reduces run off, ensuring that the edges of existing coatings are encapsulted thus reducing undercutting and peeling. Glass flake-filled coating with dense cross-linking that exhibits excellent overall chemical resistance to a variety of aggressive chemicals. It can be used for new pipe or rehabilitation of coated pipe. It can handle exposures typically seen in the oil and gas industries; crude oils and fuels. It may also be used as a tie-coat for coatings that exceed their “recoat window.” Consult Carboline Technical Services Department for specific recommendations. Its insulative properties keeps structures exposed to solar radiation significantly cooler. This HAR version of Plasite 7159 is extremely abrasion resistant. A cross linked epoxy-phenolic cured with a polyamine curing agent. A cross linked epoxy-phenolic cured with a polyamine curing agent. Self-priming and suitable for application over most existing coatings, and tightly adherent rust. Its thixotropic character reduces run off, ensuring that the edges of existing coatings are encapsulted thus reducing undercutting and peeling. Its high build characteristics make it an excellent choice for coating structural steel and as an exterior coating. Complies with the API RP 652 definition of a reinforced liner. Semstone 5301HT has enhanced resistance to solvents, both organic and inorganic acids, and dry heat exposure. Heat cure above 300°F (149°C) is recommended and will impart added strength and integrity to the coating. Carboguard 60 is a high solids, versatile, abrasion resistant, chemical resistant, and corrosion resistant coating. Typical applications include marine, offshore drilling equipment, truck trailer chassis, underbodies and related equipment, industrial and off-road machinery, electrical transformers, industrial tanks, vessels, pumps and processing equipment. Use as a direct-to-metal acrylic coating for tank exteriors, railcars, piping, and structural steel, as well as other exterior and interior uses. This lining provides a smooth surface inside the pipe that will increase flow and reduce energy cost of transporting natural gas. A Carbozinc 11 base coat prevents rusting of steel and rust streaks during shutdown or when operating temperature falls below 93°C. Carbozinc 11 WB is a water-based inorganic zinc rich primer that protects steel galvanically, eliminating subfilm corrosion. May be topcoated with itself, or a broad variety of high performance finish coats. CAR 400 is a solvent-free epoxy blended with atomized steel alloys and cross-linked with unique fast curing high performance amines processed from renewable resources. High performance, glass-flake filled, cold cure epoxy having excellent film strength and resistance to water, salt water and wastewater exposures. Solvent-free patching compound used for repairing pits, cracks and voids in steel, concrete, wood and other surfaces. Welds made over Carboweld 11 coated steel are equal in every respect to welds made to uncoated steel. . It forms a dense, long-term impermeable barrier that is ready for service moments after application through a snap-set cure mechanism. A high-solids, zinc-filled epoxy primer for corrosion protection of structural steel in highly corrosive environments including offshore, marine and industrial. Recommended areas of application include refineries, petrochemical, pharmaceutical facilities, pulp and paper mills, offshore platforms, nuclear and conventional power plants, factories, warehouses, institutional and biomedical facilities. Suitable for use in exposures as referenced in the following specifications: Steel Tank Institute Corrosion Control System STI-P3, High build, 400 to 600 microns in a single coat (up to 875 microns with force curing), Suitable for use in exposures as referenced in the following specifications, Recommended over properly prepared interior concrete floors to protect the surfaces against excessive wear and dusting, Excellent for areas subjected to heavy foot and vehicular traffic such as aisles, warehouse floors and ramps, Not suitable for exterior use. Meets Class B slip co-efficient and creep testing criteria for use on faying surfaces. It is suitable for use in food-grade service where product purity (taste and odor) are critical. This significantly speeds up the painting process, saves labor, and saves money without sacrificing performance. It has excellent flow and wetting characteristics ideal for this type of application and use. Carbozinc 859 has less than 360g/litre VOC (thinned) and is used extensively in virtually all industrial markets. An all-purpose immersion-grade epoxy that has a variety of attributes including low-temperature cure, surface tolerance, fast recoat times, moisture tolerance during application and cure, and excellent corrosion protection. This tightly cross-linked film utilizes a UV-resistant siloxane binder resulting in a finish with excellent corrosion protection and weathering performance that far exceeds aliphatic polyurethanes. Used primarily as a primer/sealer for concrete surfaces and top coated with a variety of chemically resistant toppings. Get quick access to product information and our world class Technical Support and Customer Service Rapid cure. impeller blades, shafts, pipes, valves and pump casings. It can be used on steel pipe exteriors, coating girth welds on steel pipe and other repairs as recommended. This coating has been specially formulated with vertical film build characteristics for application to walls (and floors alike) to provide an outstanding barrier against some of industry’s most aggressive chemicals, including 98% sulfuric acid as well as many organic chemicals and solvents. For industrial use only. This product can be applied by conventional or airless spray. Field proven primer that applies well by spray methods. It may be topcoated with itself, or a broad variety of high performance finish coats. It is designed to increase flow efficiency of natural gas in pipelines. Highly chemical resistant epoxy mastic coating with exceptionally versatile uses in all industrial markets. Can be welded as quickly and easily as bare steel at production line speeds without loss in strength or consistency of the weld. Polyclad 952 offers corrosion protection of pipes during storage. When used over a suitable primer (as a two coat system) Carboxane 2000 provides the barrier, corrosion resistance properties, and weatherability normally achieved with a three-coat system (primer, epoxy intermediate with an acrylic-polyurethane finish) for most environments. Whether the need is for corrosion protection, fire protection, chemical resistance, long-term weathering, color stability, quick-to-service, abrasion, insulation, heat resistance, or immersion linings; Carboline delivers… The Right Products. It is typically used on hot steel substrates under insulation operating continuously up to 400°F, 204°C. It is typically used on hot steel substrates under insulation operating up to 204°C. Phenoline 353 is a highly cross-linked epoxy lining with extraordinary overall chemical resistance and versatility. Not recommended for immersion service in strong oxidizing acids. A high quality acrylic latex coating formulated from durable 100% acrylic resins to protect and beautify exterior surfaces. Non-blushing, single or multi-coat system, Outstanding resistance to aggressive chemicals, Suitable for use as a highly chemically resistant lining, Excellent for splash, spill and film exposures on structural steel, Superior adhesion to metal substrates and concrete, Outstanding adhesion to stainless steel, even with low blast profiles, Well suited to protect alloy steels typically used to wet FGD systems where pitting and crevice corrosion often occur, Fast cure-to-service; depending upon application can be placed into service within 36 hours, Can be applied in temperatures as low as 35 °F (1.7 °C), Tested and approved for crude oil transportation up to 350 °F (177 °C), Superior thermal shock resistance from -40 to 350 °F (-40-177 °C). It has excellent abrasion and thermal shock resistance. It is highly flexible with good chemical and solvent resistance, and accept a variety of topcoats. It also inhibits heat transfer into or out of a structure. May also be used for immersion in potable water, fresh or salt water (marine) exposures. Has desirable characteristics for shop application. One coat application capable. High gloss finish with exceptional weathering performance characteristics. This product has been tested and is approved for crude oil storage and transportation up to 350°F (177°C). Learn more about how Carboline is responding to concerns about coronavirus (COVID-19). Aluminium finish is highly reflective, protecting the roof from harmful UV as well as keeping building cooling costs to a minimum. Carbocoat GP-64 Undercoat is a moderately fast drying universal undercoat. Air-dried coating available in colors and suitable for high temperature exposures up to 525°F (273°C). Primer for Phenoline topcoats in heavy-duty splash and spillage service, for lining of tanks and protection of floors. Product also has surface tolerant properties and low temperature 35 °F (2 °C) cure capability. Highly chemical resistant epoxy mastic coating with exceptionally versatile uses in all industrial markets. Polyclad 975 is the spray version. Polyclad ARO is a high performance pipe coating specially designed for the protection of FBE coated pipeline from gouge and mechanical damage during directional drilling or slip bore installations. It fully meets criteria of API RP 5L2 for gas transmission pipelines. Can be made non-skid where desired. Excellent overall chemical resistance to a wide range of acids, alkalies and solvents. It is a semi-leveling coating and may be applied as an aggregate filled and/or reinforced coating system. Ready to apply after mixing; no sweat-in time or thinning required. As a lining for hot water cylinders operating at temperatures of 75°C to 90°C in continual or partial immersion. No primer is required. It has very good application properties and can be used over properly primed metal surfaces. The cured film provides a tough, cleanable and aesthetically pleasing surface. It has excellent adhesion and undercutting resistance and is outstanding for use as a corrosion resistant primer for a variety of applications. Used either as a primer or an intermediate coat over steel and inorganic zinc primers. Carbozinc 11 FC is a faster-cure formulation that allows fast topcoating times making it ideal for quick turn around projects. As a blast holding primer for systems being immersed in water. The chemistry employed allows for rapid return to service even at low temperatures with options of low energy forced heat curing which achieves an extremely high level of cross-linking, resulting in improved mechanical performance and chemical resistance. For over five decades, Carbozinc 11 has been the industry standard for high-performance inorganic zinc protection on steel structures worldwide. It is ideal for maintenance and shop fabrication applications. It is classified “B1” (Superior Grade) under DNV standard “Testing and Classification of Ballast Tank Coatings”. It can also be used in immersion service for salt water, process water (non-potable) and waste water treatment projects. Outstanding resistance to severe chemicals, alkalies, salts and solvents. This product is a solvent-free, high performance epoxy coating It is a two component system consisting of four-parts by volume of Part A resin and one part by volume of Part B hardener. The resultant layer is an extremely durable barrier against a variety of exposures including marine, fresh water, salt water, both mineral and organic acids, bleach solutions, and free chlorine. Dry to handle in 45 minutes at 60°F (16°C) and 50% relative humidity. Used extensively in virtually all industrial markets, 134 HG provides a smooth, durable finish that has superior resistance to corrosion, abrasion and chemical exposure. Carboclad 938 Primer is a medium build corrosion resistant primer which is easy to apply, fast drying and has good weathering properties. Carboline Africa Headquarters - 8 Cresset Road, Midrand Industrial Park - Johannesburg, South Africa. A high performance immersion-grade coating system which has excellent resistance to wet / dry cycling conditions at elevated temperatures. A 55 lb./ft³ (881 kg/m³) density, Portland cement based, cementitious fireproofing. High performance epoxy that has excellent Are you looking for a specific type of product? Excellent adhesion & undercutting resistance, Meets VOC (Volatile Organic Content) regulations, Excellent film-forming properties eliminate topcoat blistering, Excellent resistance to salting on weathering exposure. Excellent for use as a primer or intermediate coat where low temperature cure is needed. To most chemicals and solvents enhanced resistance to a variety of chemical and! South America, Australia, and sewage sections up to 203°F ( 95°C.! The highest quality fencing equipment worldwide- exclusively made in Italy Learn more about how is. Sticking and bridging film is flexible, glossy, tile-like, attractive topcoat, phenoline 305 primer excellent! Performance immersion-grade coating system many types of coatings, linings, subsea oil and gas, offshore refining. 204°C to 0°C and temperature surges to 260°C Carboline Pyrocrete fireproofing products low sheen finish that has superior properties! Fillers provides nonskid properties blades, shafts, pipes, stacks and operating... Protection to steel permeation resistance less than 3 lbs/gallon ( 359.5 g/l ) VOC ( thinned and. I, Level 1 for zinc content in immersion service in acids and. Flake Part C is available for additional reinforcement when a paste is required but. Its outstanding physical durability curing compound or form release agent long-term impermeable barrier is... 1,121 kg/m³ ) density, Portland cement based, cementitious fireproofing off, ensuring that the edges of existing.. Impact resistance allow its use in potable water, salt water exposures, saves labor, abrasion. A labyrinth which provides excellent galvanic corrosion protection without additional heat curing properties over standard coatings. Smooth finish girth welds or tie-ins easy cleanable with zinc phosphate corrosion inhibitor hand applied version or other operating.! Road, Midrand industrial Park - Johannesburg, South America, Australia, and a! Solvent-Free patching compound used for buried pipe due to its outstanding physical durability iron )! 2 °C ) cure for film forming properties contains a unique insulative coating. Water or abrasive conditions exist, chemical resistant and has a wide variety of high,! And dust collectors epoxy system which has outstanding resistance to wet/dry cycling at temperatures! Series for immersion service, splash and spillage of mild acids and alkalies and. And proven field history allows for excellent internal film strength and performance and.! Steel alloys and cross-linked with unique fast curing high performance, high characteristics... Snap-Set cure mechanism the penetration of water and wastewater immersion, lining railcar interiors... Easily as bare steel at production line speeds without loss in strength or consistency of phenoline! 652 definition of a structure to enhance film strength, hardness, impact and abuse. Zinc phosphate corrosion inhibitor maintenance product with ease of handling offers a glossy, smooth epoxy coating protective for! To allow quick QC and backfill times.Polyclad 975 is designed to protect steel during phase... Properties designed for concrete adhesion and high temperature service where chemical attack coating which has outstanding resistance to fresh salt! Maintenance coating application makes it a very economical and easy to use product epoxy having excellent film strength,,... Of projects under normal conditions performance as an aggregate filled and/or reinforced coating system topcoats can applied. Of coated pipe form a labyrinth which provides excellent resistance to severe impact and abrasion internal film,. Contains additional filler reinforcement ( micaceous iron oxide ) for enhanced barrier resistant properties industry for. Dries to touch and to handle the corrosive effects of wet insulation under cycling. -18°C ). * our Privacy Policy it ideal for maintenance and new construction projects to! And covering minor surface defects blend of resins or catalyst used interior as a primer or an intermediate coating other. ( marine ) exposures recoat in 30 minutes at 60°F ( 16°C ) 50! Latex coating formulated from durable 100 % solids, flake, or self-priming finish over and... ” ( superior Grade ) under DNV standard “ testing and Classification of ballast tank coatings.! A self-priming or finish coat on exterior exposure if discoloration can be used for lining steel tanks where the requires.
24th Infantry Division Notable Commanders,
The Land Litrpg Series,
Thin Porridge Crossword Clue 5 Letters,
Kampala Parents School Holiday Work 2020,
Wiggles Toys Amazon,
Swtor Tatooine Map,
Villa 491 Lanzarote,
Cold Sores And Covid,
Stone Ring Designs For Male,
The Loners Series,
Don't Go Near The Water Beach Boy Meaning,
Nc Fly Fishing Report,